Skip to content

About

A portable LoRa communicator. Custom 4-layer PCB (ESP32-S3 + E22P-915M30S LoRa + NEO-M9N GNSS), designed in KiCad for 915 MHz.

Topics

Resources

Stars

8 stars

Watchers

0 watching

Forks

Latest commit

 

History

191 Commits

Folders and files

NameName
Last commit message
Last commit date
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

parsnip-node

A rugged, self-contained Meshtastic/MeshCore LoRa node for outdoor use. It combines an ESP32-S3 host, an Ebyte E22P-915M30S LoRa module (SX1262 + PA, up to 30 dBm / 1 W), and a u-blox NEO-F10N dual-band (L1 + L5) GNSS receiver, and runs off two 21700 Li-ion cells in series that charge over USB-C PD or solar. Designed in KiCad for 915 MHz operation in Canada under ISED RSS-247.

The aim is a node that non-technical people can use without a phone: one of the longest-range, best-value LoRa front ends, accurate GNSS, days of runtime, and protection on every external port.

parsnip-node v2 on a turntable: E-Ink module on the front, two 21700 cells on the back
Render, see (code/render), with two 21700 cells and the optional WeAct 3.7" E-Ink module on M2 standoffs and a clear top plate. The display mount is a mock-up, not part of the board yet.

Status

v2 (this design): schematic complete, PCB placed and fully routed (478 footprints, every net one piece of copper). Prototype fab and assembly are being arranged with PCBWay. Firmware bring-up starts once boards arrive.

v1 (single 18650, XIAO ESP32-C6, 55 x 100 mm) was built and field-tested; photos are at the bottom. The design log is in JOURNAL.md.

Features

Block Implementation
Host ESP32-S3-WROOM-1U-N16R8 (16 MB flash, 8 MB octal PSRAM), U.FL 2.4 GHz antenna. The footprint is the WROOM-1 land pattern, so the PCB-antenna module also fits.
LoRa E22P-915M30S, 915 MHz, up to 30 dBm, SMA. An antenna-detect FET inhibits TX when no antenna is attached.
GNSS NEO-F10N, L1 + L5 (NEO-M9N footprint-compatible fallback). Active antenna on SMA or U.FL, switched bias-tee, dual-band SAW, 6 dB pi pad. Coin-cell backup for hot starts.
Battery 2S 21700 Li-ion in SMD holders on the back. MAX17320 fuel gauge, protection and cell balancing.
Charger BQ25798 buck-boost NVDC charger with dual-input power mux (USB-C or solar). Regulated ~7-8.4 V system rail.
USB-C TPS25751 PD controller: sink, and source (OTG) up to 20 V @ 3 A. TPD8S300 OVP/ESD on CC/SBU, liquid detection. USB 2.0 full speed to the ESP32-S3.
Rails Two LM61460 low-EMI bucks (5 V, 3.3 V), synchronised 180 deg out of phase at 2 MHz. TPS25947-family eFuses on the 5 V and GNSS rails.
Sensors LSM6DSV16X 6-axis IMU, QMC6309 magnetometer.
I/O 16-pin GPIO expander header (TCAL9539), Qwiic and 2.54 mm I2C ports, SPI expansion, E-Ink header, 2 x WS2816B RGB LEDs plus an external LED port, debug UART.
Board 60 x 130 mm, 4 layers, 1.6 mm, ENIG, black mask.

All charger and battery-path parts are rated for 4S (caps 25 V minimum, mostly 50 V) even though the pack is 2S.

Architecture

Block diagram
Block diagram
Power tree
Power tree

Power flows cells -> fuse -> MAX17320 protection FETs -> BQ25798 -> VSYS (regulated, not raw battery) -> the 3.3 V and 5 V bucks. The 5 V rail feeds the E22P, the LED port and the GNSS antenna bias. The GNSS module gets its own LDO and eFuse off 5 V. USB-C (through the PD controller) and solar each have their own FET path into the charger, and the first valid input wins.

Schematic

The full schematic is parsnip-schematic.pdf (12 pages: cover, block diagram, power tree, then the circuit sheets). Click a page for full size.

ESP32-S3 MCU schematic
ESP32-S3 MCU
LoRa front end schematic
LoRa (E22P-915M30S)
GNSS and active antenna schematic
GNSS (NEO-F10N)
5 V and 3.3 V buck regulators schematic
5 V / 3.3 V bucks
Charger and power path schematic
Charger / power path
BMS schematic
BMS (MAX17320)
USB-C PD schematic
USB-C / PD
Peripherals schematic
Peripherals
Connectors schematic
Connectors

PCB

PCB render, front at an angle
Front
PCB render, back at an angle
Back
PCB render, top
Top
PCB render, bottom
Bottom (21700 holders)
  • 60 x 130 mm, 4 layers, 1.6 mm total, 1 oz copper on all layers, ENIG
  • Stackup (JLCPCB JLC041611-7628 equivalent): F.Cu / 0.203 mm prepreg (Er 4.4) / In1 / 1.03 mm core / In2 / 0.203 mm prepreg / B.Cu
  • In1 is a solid GND reference for all RF. RF lines are 0.306 mm on F.Cu, 49-53 ohm field-solved with mask, mostly CPWG with GND via fences well under lambda/20
  • ~2100 vias (0.3 mm and 0.2 mm drill), most of them GND stitching
  • The cell holders take most of the back, so everything above them is single-sided

Hardware

Part Price
PCB + assembly (BOM) being quoted
2 x Samsung 58E 21700 cells 18650batterystore.com $40 CAD
WeAct 3.7" E-Ink module, 240 x 416, optional AliExpress $25 CAD

Production files (gerbers, BOM, pick-and-place) are in production/. Datasheets for every IC, module and connector are in docs/datasheets/, sources in SOURCES.md.

ESP32-S3 GPIO map

GPIO numbers are ESP32-S3 GPIO, not module pins. Reference designators can change during layout; the schematic is authoritative.

LoRa: E22P-915M30S

Signal GPIO
NSS 10
SCK 12
MOSI 11
MISO 13
BUSY 14
DIO1 4
NRST 40
EN 41

T/R switching comes from the module's DIO2 (setDio2AsRfSwitch(true)), not a GPIO.

GNSS: NEO-F10N

Signal GPIO
TXD (to host RX, UART1) 1
RXD (from host TX, UART1) 2
TIMEPULSE 3
EXTINT 48

The module's I2C/SPI pins reach the host I2C bus only through solder jumpers, for the NEO-M9N fallback. The F10N uses UART only.

Other

Function GPIO
I2C SDA / SCL (host bus) 8 / 9
I2C IRQ (PD controller, fuel gauge, GPIO expander) 7
E-Ink header: BUSY / RESET / D/C / CS 5 / 6 / 18 / 17
SPI expansion header CS 38
USB D- / D+ 19 / 20
UART0 TX / RX (debug header) 43 / 44
32.768 kHz RTC crystal 15 / 16
BOOT 0
eFuse power-good: 5 V / GNSS 3.3 V 39 / 42
EMI sync clock gate 47
RGB LED data (via 5 V level shifter) 46
5 V buck disable (high = off) 21
Octal PSRAM (reserved) 35 / 36 / 37
VDD_SPI strap (not connected) 45

I2C addresses

Bus Device Address
Host (GPIO 8/9) TPS25751 USB-PD controller 0x20
Host MAX17320 fuel gauge 0x36, 0x0B
Host LSM6DSV16X IMU 0x6A
Host TCAL9539 GPIO expander 0x74
Host QMC6309 magnetometer 0x7C
PMIC (owned by the TPS25751) BQ25798 charger 0x6B
PMIC M24512 EEPROM (PD config) 0x50

Firmware

Firmware is a Meshtastic fork, tracked as the firmware submodule (LimesKey/firmware). A device variant declares the pin map above and the PA control lines so TX keys up. The GNSS is on UART1, which stock Meshtastic supports.

git clone --recurse-submodules https://github.com/LimesKey/parsnip-node.git

Repository layout

Path Contents
parsnip.kicad_pro KiCad project (KiCad 10.99 nightly format; stable 10.0 cannot open it)
*.kicad_sch Schematic sheets: seven top-level sheets plus five sub-sheets under the MCU page
parsnip.kicad_pcb Board
lib/ Project symbols, footprints and 3D models
production/ Gerbers, BOM, pick-and-place
docs/ Datasheets and photos
JOURNAL.md Design log
v1/ The previous single-cell board

v1 in the field

Assembled v1 board on the bench
Assembled board
v1 during outdoor testing, front
Outdoor testing
v1 during outdoor testing, back
Outdoor testing, back

License

CC BY-NC-SA 4.0

About

A portable LoRa communicator. Custom 4-layer PCB (ESP32-S3 + E22P-915M30S LoRa + NEO-M9N GNSS), designed in KiCad for 915 MHz.

Topics

Resources

Stars

8 stars

Watchers

0 watching

Forks

Releases

Packages

Contributors

Languages